two balloons are inflated at the same temperature to the same volume, though it takes more gas to inflate the balloon on the right.

Answers

Answer 1

If one balloon requires more gas to inflate, then either the temperature or the volume must be different between the two balloons

The situation you described is not possible if both balloons are inflated at the same temperature and to the same volume. According to the ideal gas law, the volume of a gas is directly proportional to the amount of gas (measured in moles) present, assuming constant temperature and pressure.

If the temperature and volume are the same for both balloons, then the number of moles of gas in each balloon should also be the same. Therefore, it should take the same amount of gas to inflate both balloons.

If one balloon requires more gas to inflate, then either the temperature or the volume must be different between the two balloons

learn more about pressure here:

https://brainly.com/question/30482677

#SPJ11


Related Questions

The speed of your automobile has a huge effect on fuel consumption. Traveling at 65 miles per hour (mph) instead of 55mph can consume almost 20% more fuel. As a general rule, for every mile per hour over 55 , you lose 2% in fuel economy. For example, if your automobile gets 30 miles per gallon at 55mph, the fuel consumption is 21 miles per gallon at 70mph. If you take a 400-mile trip and your average speed is 83mph rather than the posted speed limit of 73mph, what is the extra cost of fuel if gasoline costs $3.26 per gallon? Your car gets 30 miles per gallon (mpg) at 63mph.

Answers

The extra cost of fuel for driving 83 mph instead of 73 mph is $3.7671.

The speed of your automobile has a huge effect on fuel consumption. Traveling at 65 miles per hour (mph) instead of 55mph can consume almost 20% more fuel. As a general rule, for every mile per hour over 55 , you lose 2% in fuel economy.

If you take a 400-mile trip and your average speed is 83mph rather than the posted speed limit of 73mph, then the extra cost of the fuel is calculated as:

* **Fuel consumption at 83 mph:** 30 mpg * (1 - 2% * (83 - 55)) = 27.6 mpg

* **Fuel consumption at 73 mph:** 30 mpg * (1 - 2% * (73 - 55)) = 29 mpg

* **Extra fuel used:** 400 miles / 27.6 mpg - 400 miles / 29 mpg = 2.4 gallons

* **Extra cost of fuel:** $3.26/gallon * 2.4 gallons = $3.7671

to learn more about the average speed here:

https://brainly.com/question/15823792

#SPJ11

Individuals who acquire a health condition with no prior family history of that condition may have had exposure to

Answers

Individuals who acquire a health condition with no prior family history of that condition may have had exposure to various environmental factors or lifestyle choices such as exposure to toxins, chemicals, or pollutants can contribute to the development of health conditions in individuals without a family history.

In some cases, genetic mutations can also occur spontaneously, resulting in the development of a health condition without any family history. Environmental factors such as exposure to toxins, chemicals, or pollutants can contribute to the development of health conditions in individuals without a family history, these factors can cause changes in the body that lead to the onset of diseases like cancer or asthma. Lifestyle choices, including diet, exercise, and stress management, can also play a significant role in the development of health conditions without a family history. Poor nutrition, sedentary lifestyle, and high-stress levels can increase the risk of developing diseases like heart disease, diabetes, and hypertension.

Furthermore, genetic mutations can occur spontaneously, which means they are not inherited from either parent, these mutations can result in the development of health conditions that have no prior family history, such as cystic fibrosis or certain types of cancer. In conclusion, exposure to environmental factors, lifestyle choices, and spontaneous genetic mutations can all contribute to the development of health conditions in individuals without a family history of that condition. It is essential to be aware of these factors and adopt a healthy lifestyle to minimize the risk of developing such conditions.

Learn more about genetic mutations at

https://brainly.com/question/11115635

#SPJ11

A camper walks away from camp. He walks 23.72m north, then 39.25m south and
then 105.06m north again. What is his total displacement?
You will need to use a (-) sign if the direction is south. Plus is assumed if no + is
included in your answer. Do not use +.

Answers

Answer:

89.53    North

Explanation:

Total N-S displacement

   23.72  -  39.25 + 105.06   =  + 89.53

A series circuit connects a single light bulb to a single power source. As more light bulbs are added to the circuit, which graph BEST represents the change in voltage to each bulb?

A series circuit connects a single light bulb to a single power source. As more light bulbs are added

Answers

Answer:

The Answer is C

Explanation:

USAtestprep

Answer:

C

Explanation:

One disadvantage of series circuits is that voltage along the circuit drops as more devices are added and turned on. This drop in voltage is shown in graph C.

how do i get the correct answer for 0.429m to mm

Answers

the answer for 0.429m to mm is 429

Answer:

0.429m=429 mm

Explanation:

Since there are 1,000 millimeters per meter, you need to multiply by 1,000 to convert from meters to millimeters.

Which of the following is most likely to make it safer while lighting the rocket?
A. decreasing the size of the cap
B. increasing the length of the fuse
C. increasing the length of the body
D. decreasing the length of the stick

Answers

While lighting the rocket you should ensure D) decreasing the length of the stick

What are the precautions you should take while lighting the rocket?

When lighting fireworks, avoid holding them in your hand or placing any part of your body over them. Don't carry fireworks in your pocket since the friction could set them off; instead, use eye protection. Keep pyrotechnics away from flammable objects, such as brush, leaves, and dwellings.

The continuous smoke from cracker explosions may sting or wet the eyes. Because bottle rockets are thought to be the riskiest cracker type, it's crucial to avoid them, keep a safe distance from the burning crackers, wear safety goggles, and avoid wearing contact lenses while popping crackers.

To know more about rockets you may visit the link:

https://brainly.com/question/15061209

#SPJ4

DO NOT ANSWER IF YOU DONT KNOW What is the medium for a wave:
i. At the beach?
ii. In a football stadium?
iii. Of sound?​

Answers

Water fans/people air

A chameleon extends its tongue to capture a tasty insect.the chameleons tongue accelerates at 33m/s^2 for 0.12s to make the capture.what is the speed of the chameleons tongue when it grabs the insect?

Answers

The required speed at which chameleon's tongue grabs the insect is calculated to be 3.96 m/s.

Acceleration of chameleon's tongue is given as 33 m/s².

Time is given as 0.12 s.

We know that, the rate of change of velocity is acceleration.

Mathematically, a = (v - u)/t

where,

v is velocity

t is time

a is acceleration

Putting the values in the equation,

a = (v - u)/t

Making v as subject,

v = a t = 33 × 0.12 = 3.96 m/s

Thus, the speed at which chameleon's tongue grabs the insect is calculated to be 3.96 m/s.

To know more about chameleon:

https://brainly.com/question/30534993

#SPJ4

Which example is of researcher bias in interpreting data?

A scientist wishes to determine the area of an ice sheet. To do so, he relies on spectrographic images sent by satellite.


A health official investigates the spread of HIV in her city. She takes a census of the HIV status of every adult resident.


A geologist wants to determine whether the water level of an aquifer is declining. To find the answer, he digs a well.


A researcher seeks to prove that babies smile at two months old. She counts some confused expressions as smiles.

Answers

Answer:

A researcher seeks to prove that babies smile at two months old. She counts some confused expressions as smiles.

Explanation:

This is the answer because its not actual date due to the fact she's using her opinion to decided whether or not the expression a baby is making is a smile, whereas the other answers had factual data involved.

for a parallel flow double pipe heat exchanger insulated from its surroundings, the mean outlet temperature of the initially cold fluid can exceed the mean outlet temperature of the initially hot fluid.

Answers

The final heat of your substance can be calculated by adding the temperature change to the starting point.Your water's final temperature would be 24 + 6, or 30 degrees Celsius, for instance,if the temperature was 24 degrees when it began.

What is the formula for the beginning temperature?

Simple: Change in temperature divided by initial temperature.Grams are used to express the mass.T=TfTi, where Transfer function is the final temperature while Ti is the initial temperature, gives the change in temperature.

What distinguishes initial from final?

In physics, an object's initial position is its starting point for motion, and its final position is where it comes to rest.

To know more about heat exchange visit:

https://brainly.com/question/22595817

#SPJ4

if the electric field is 108 n/c at a distance of 59 cm from a point charge q, what is the value of q (in c)? (enter the magnitude.)

Answers

If the electric field is 108 n/c at a distance of 59 cm from a point charge q,  the charge on the point charge is 9.98 x \(10^{-19}\) Coulombs.

We can use the equation for the electric field produced by a point charge to find the charge:

E = k * q / \(r^{2}\)

where,

E = the electric field, equal to 108 N/C

k = the Coulomb constant, equal to 8.99 x \(10^{9}\) N \(m^{2}\) / \(C^{2}\)

q = the charge

r = the distance from the point charge, equal to 59 cm = 0.59 m

Rearranging the equation to solve for q, we get:

q = E * \(r^{2}\) / k

Plugging in the values, we get:

q = 108 N/C * \((0.59 m)^{2}\) / 8.99 x \(10^{9}\) N \(m^{2}\) / \(C^{2}\) )

q = 9.98 x \(10^{-19}\) C

So the charge on the point charge is 9.98 x \(10^{-19}\) C, or 9.98 x \(10^{-19}\) Coulombs.

Here you can learn more about the magnitude

brainly.com/question/28327873

#SPJ4

Part 1: How many "pathways" are in this circuit?
Part 2: Therefore, is this a series or parallel circuit?

Part 1: Zero pathways
Part 1: One pathway
Part 1: Two pathways
Part 1: Three pathways
Part 1: Four pathways
Part 1: Five pathways
Part 2: Series circuit
Part 2: Parallel circuit

Part 1: How many "pathways" are in this circuit?Part 2: Therefore, is this a series or parallel circuit?Part

Answers

Part 1: The number of pathways in a circuit determines the possible routes for electric current to flow.

There are maximum of five pathways in this circuit, depending on its complexity and the arrangement of components.

Part 2: Determining whether the circuit is series or parallel requires more information.

In a series circuit, components are connected in a single path, and the current flows through each component sequentially.

If the circuit has only one pathway (zero or one pathway), it suggests a series circuit.

However, if the circuit has multiple pathways (two or more pathways), it indicates a parallel circuit.

To conclusively determine the circuit's nature, we need to analyze the circuit diagram or obtain additional details regarding the component connections and their interactions.

For such more questions on electric current

https://brainly.com/question/30033550

#SPJ8

Is this conversion correct?
11.3g/ cm^3 to kg/ m^3
Since 1000 g = 1 kg and 100 cm = 1 m
Therefore, (11.3 x 1000)/ 100
= 113 kg/ m^3

Answers

11.3 g/cm³ equals to 1130  kg/m³.

What is density?

The mass of a substance per unit of volume is its density. Density is most frequently represented by the symbol ρ, however Latin letter D may also be used. Density is calculated mathematically by dividing mass by volume.

Given that 11.3 g/cm³.

Know that

1000 grams = 1 kg

1 grams = 1/1000 kg.

100 cm = 1 m

1 cm = 1/100 m.

Therefore, 1 cm³ = (1/100)³ m³

= 1/1000000 m³

Hence, 1  g/cm³ = (1/1000) ÷ (1/1000000)  kg/m³

= 1000000/1000 kg/m³

= 1000 kg/m³.

Hence, 11.3 g/cm³ = (11.3 × 1000) kg/m³

= 1130  kg/m³

Hence, 11.3 g/cm³ equals to 1130  kg/m³.

Learn more about density here:

https://brainly.com/question/29775886

#SPJ1

A person on a bike (m = 90 kg) is traveling 4 m/s at the top of a 2 m hill. what is the biker’s total energy?

Answers

At the summit of a 2 m hill, a cyclist (m = 90 kg) is moving at a speed of 4 m/s. The rider would have 2484 Joules of total energy.

What is mechanical energy?

Total kinetic energy, which represents all the energy in motion, and total potential energy, which represents all the stored energy in the system, combine to form mechanical energy.

As stated in the problem, a cyclist (m = 90 kg) is climbing a 2 m hill at a speed of 4 m/s.

The total kinetic energy of the biker

KE = 1/2 × m × v²

 = 0.5 × 90 × 4²

  = 720

Similarly, the total potential energy of the biker

PE = m × g × h

 =90 × 9.8 × 2

= 1764 Joules

The biker's total energy is equal to 720 plus 1764.

                                     = 2484 Joules

The biker's overall energy would therefore be 2484 Joules.

To know more about mechanical energy visit:-

https://brainly.com/question/13552918

#SPJ4

Example of electrical to sound? And explain how the energy is changing forms?

Answers

microphone for example

By measuring the length of the skid marks, an accident investigator determines that the distance a car travelled between the brakes being applied and stopping was 22 m.

The investigator used a sled to determine the friction. The investigator then calculated that the car decelerated at 7.2 m / s2.
Calculate the speed of the car just before the brakes were applied.

Please help, i’m so confused!!

Answers

The initial velocity of the car just before the brakes were applied is 17.80 m/s

Given parameters

From the question given above, the following data were obtained:

Distance (s) = 22 mDeceleration (a) = -7.2 m/s²Final velocity (v) = 0 m/sInitial velocity (u) = ?

How to determine the initial velocity of the car

The initial velocity of the car can be obtained as illustrated below:

v² = u² + 2as

0² = u² + (2 × -7.2 × 22)

0 = u² + (-316.8)

0 = u² - 316.8

Collect like terms

u² = 0 + 316.8

u² = 316.8

Take the square root of both side

u = √316.8

u = 17.80 m/s

Thus, we can conclude that the initial velocity of the car before the brakes were applied is 17.80 m/s

Learn more about velocity:

https://brainly.com/question/21010554

#SPJ1

A student shakes a rope such that 36 complete vibrations are
made in 9.00 seconds. determine the vibrational period of
the rope, along with the corresponding unit.

Answers

The vibrational period of the rope, when a student shakes it is 0.25 s.

What is the frequency?

Frequency is the number of oscillations per second.

Given is the number of vibrations =36 in time t = 9s, then frequency will be

f = 36/9 =4Hz

The time period is the reciprocal of the frequency.

T = 1/f

Plug the frequency value, we get

T = 1/4 Hz = 0.25 seconds

Thus, the vibrational time period is 0.25s.

Learn more about frequency.

https://brainly.com/question/25867078

#SPJ1

1. the wavelength of a particular color of violet light is 414 nm. calculate the frequency of this color.

Answers

The violet color has a frequency of 7.24 x (10)^14 / sec based on the wave length provided.

What wavelength is it?

A waveform signal that is carried in space or down a wire has a wavelength, which is the separation between two identical places (adjacent emblems) in the consecutive cycles. This length is typically defined in wireless systems in metres (m), centimeters (cm), or millimeters (mm) (mm).

Briefing :

we know that, f = frequency = 1/wavelength = c/λ

where c = speed of light = 299 792 458 m / s or 3 x 10^{8} m/s

and given wavelength ( λ)=414 nm

1 nm = 10^{-9} m

so, λ= 414 x 10^{-9} m

therefore f= frequency= 7.24 x (10)^14 / sec.

To know more about wavelenght visit :

https://brainly.com/question/1263539

#SPJ4

A 2.00 KG brick falls from the top of a building 6.00 M above the ground. What is the kinetic energy of the brick just before it reaches the ground

Answers

Answer:

the kinetic energy of the brick before it reaches the ground is 117.6 J.

Explanation:

Given;

mass of the brick, m = 2 kg

height of the building, h = 6 m

The kinetic energy of the brick before it reaches the ground is maximum.

Based on the principle of conservation of energy, the maximum potential energy = maximum kinetic energy

K.E = P.E = mgh

where;

g is the acceleration due to gravity = 9.8 m/s²

K.E = 2 x 9.8 x 6

K.E = 117.6 J

Therefore, the kinetic energy of the brick before it reaches the ground is 117.6 J.

Which of the following are
mechanical waves?
A. waves that travel in empty space
B. sound and ocean waves
C. light waves
D. x-rays

Answers

It’s b for sure since the waves move on the ocean

Answer:

sound waves are mechanical waves

Explanation:

Mechanical waves needs a media through which they can transmit, and media must have elasticity

Charging an Insulator A small metal ball is given a negative charge, then brought near (i.e., within a few millimeters) to end A of the rod. What happens to end A of the rod when the ball approaches it closely this first time?

Answers

When the negatively charged metal ball is brought near end A of the rod, the phenomenon known as induction occurs, that is, end A becomes polarized, with the side closer to the ball acquiring a positive charge and the side farther away acquiring a negative charge.

When the negatively charged metal ball is brought close to end A of the rod, the negative charge on the ball repels the electrons in the rod, causing them to move away from the ball and redistribute along the rod. This redistribution of charge leads to a separation of charges within the rod.

The end of the rod closest to the ball (end A) experiences a deficiency of electrons due to their repulsion, resulting in a positive charge. This positive charge is induced by the presence of the negatively charged ball. Meanwhile, the end of the rod farthest from the ball acquires an excess of electrons and, therefore, a negative charge.

This polarization of the charges at the ends of the rod is a temporary effect that occurs when the negatively charged ball is in close proximity to end A. It does not involve the transfer of charge between the ball and the rod but rather a redistribution of existing charge within the rod.

This polarization occurs due to the repulsion of electrons by the negatively charged ball, causing a redistribution of charges within the rod.

To know more about Induction, visit

brainly.com/question/26366866

#SPJ11

A young diver is practicing his skills before an important team competition. Use the diagram below in order to analyze the energies of the diver and complete the statements below.

Where m = mass (kg), g = 9.8 m/s2, v = velocity (m/s), h = height (m), KE = kinetic energy (J), and GPE = gravitational potential energy (J).
Use the equations above to answer the following questions.

A diver with a mass of 90 kg is at a height of 10 m, and he has not jumped off of the board yet (v = 0 m/s). When the diver reaches a height of 5 m (Point C), his gravitational potential energy is

A. 1350 J

B. 8820 J

C. 4410 J

D. 0 J

and his velocity is

E. 4.5 m/s

F. 0 m/s

G. 3.2 m/s

H. 9.9 m/s

Please help will mark brainliest

A young diver is practicing his skills before an important team competition. Use the diagram below in

Answers

Mass of the diver (m) = 90 Kg.Height of the board from the ground (h) = 10 m.Acceleration due to gravity (g) = 9.8 m/s^2.Height of the diver from the ground when he reaches point C (x) = 5mInitial velocity (u) = 0 m/sWe know, gravitational potential energy of a body = mass × acceleration due to gravity × height.Therefore, the gravitational potential energy of the diver when he reaches point C (GPE) = mg(h - x)or, GPE = [90 × 9.8 × (10-5)] Jor, GPE = [90 × 9.8 × 5] Jor, GPE = 4410 JFor a freely falling body,v^2 - u^2 = 2ghor, v^2 = 2ghWe know, kinetic energy of a body = 1/2 mv^2Therefore, kinetic energy of the diver when he reaches point C (KE) = 1/2 m(2gx)Here, 2gx = (2 × 9.8 × 5) = 98 (m/s)^2We have already seen v^2 = 2gh or, v = √2ghSo, the velocity of the diver = √2gx = √98 m/s = 9.9 m/s

Answers:

The gravitational potential energy of the diver when he reaches point C is 4410 J.

The velocity of the diver is 9.9 m/s.

Hope you could get an idea from here.

Doubt clarification - use comment section.

h=10m-5m=5mm=90Kgg=9.8m/s^2

\(\\ \sf\longmapsto PE=mgh\)

\(\\ \sf\longmapsto PE=90(5)(9.8)\)

\(\\ \sf\longmapsto PE=4410J\)

Now

It's converted to kinetic energy while reaching ground.

\(\\ \sf\longmapsto K.E=4410\)

\(\\ \sf\longmapsto \dfrac{1}{2}mv^2=4410\)

\(\\ \sf\longmapsto 90v^2=8820\)

\(\\ \sf\longmapsto v^2=98\)

\(\\ \sf\longmapsto v=9.9m/s\)

What single color of light illuminating a ripe banana will make it appear black?.

Answers

The single color of light illuminating a ripe banana will make it appear black will be blue light.

When lit with blue light, ripe bananas appear black. Yellow is a combination of red and green, so if blue light is flashed onto a yellow banana, the fruit will absorb the blue light, leaving nothing for the banana to reflect. The banana seems black to the eyes because there is nothing for them to reflect back to them. So, when viewed with blue light, a ripe banana appears black.

A red shirt would seem black if only blue light were shined on it because no red light would be there to reflect the blue light, which would otherwise absorb it. Ripe bananas adhere to the same standard and also white objects, which seem white because they reflect all colors.

Learn to know more about Light on

https://brainly.com/question/19697218

#SPJ4

What is the frequency of a wave that passes a given point 412 times in 4.0
seconds?
O A. 0.0097 s
OB. 103 Hz
O C. 408 S
O D. 1650 Hz
SUBMIT

Answers

Answer: A.0,0097s

Mas a unidade aí deveria ser Hertz (Hz)

Explanation:

What is the frequency of a wave that passes a given point 412 times in 4.0seconds?O A. 0.0097 sOB. 103

Answer:

103 hz

Explanation:

What is the gravitational force that two objects would feel if they are 3.5 meters apart? Object 1 has a mass of 10x10^5 kg and object 2 has a mass of 3x10^5 kg?

Answers

Answer:

1.63 N

Explanation:

F = GMm/r^2

  = (6.67x10^-11)(10x10^5)(3x10^5) / 3.5^2

  = 1.63 N  ( 3 sig. fig.)

A steel plate (50 x 50 x 0.5 cm ) is to be cast using the sand casting process. If the liquid shrinkage of the steel during solidification is 3%, calculate the following - [1+2+2] a. Volume of molten metal required to avoid shrinkage b. Calculate the dimension of a cubical riser to avoid shrinkage c. Check the adequacy of the riser using Cain's method

Answers

To avoid shrinkage in a steel plate cast using sand casting, the volume of molten metal required is calculated considering the 3% liquid shrinkage. A cubical riser with a dimension of approximately 3.37 cm can be used to compensate for the shrinkage, but a comprehensive evaluation using Cain's method requires more specific information.

a. To calculate the volume of molten metal required to avoid shrinkage, we need to consider the liquid shrinkage of the steel. The liquid shrinkage is given as 3%, which means the solidified steel will have a volume that is 3% less than the molten metal volume. Therefore, we can calculate the volume of molten metal required as follows:

Initial volume = (50 cm) x (50 cm) x (0.5 cm) = 1250 cm³

Volume of molten metal required = Initial volume / (1 - shrinkage)

                            = 1250 cm³ / (1 - 0.03)

                            = 1288.66 cm³

b. To calculate the dimension of a cubical riser to avoid shrinkage, we need to determine the additional volume required to compensate for the shrinkage. Since the liquid shrinkage is 3%, the riser should have a volume equal to 3% of the volume of the steel plate. Therefore:

Volume of the riser = 0.03 x Volume of the steel plate

                  = 0.03 x 1250 cm³

                  = 37.5 cm³

To calculate the dimension of a cubical riser, we can assume all sides are equal. Let's denote the side length of the riser as "x." Then, the volume of the riser can be expressed as:

Volume of the riser = x³

Solving for x, we find:

x = ∛(Volume of the riser)

 = ∛37.5 cm³

 ≈ 3.37 cm

Therefore, the dimension of the cubical riser should be approximately 3.37 cm.

c. Checking the adequacy of the riser using Cain's method requires additional information and calculations related to solidification time, cooling curves, and feeding range. Without these specific details, a comprehensive evaluation using Cain's method cannot be performed within the given context.

To know more about molten metal,

https://brainly.com/question/20238990

#SPJ11

What atmospheric constituent is responsible for the blue color of uranus and neptune?.

Answers

Answer:

Neptune's atmosphere is made up predominately of hydrogen and helium, with some methane. The methane is part of what gives Neptune its brilliant blue tint, as it absorbs red light and reflects bluer colors. Uranus also has methane in its atmosphere, but has a duller shading.

Explanation:

The low temperatures of these distant planets allow for the formation of methane clouds that contribute to the blue color.

hope it's help you.....

A 2. 0 kg mass starts from rest and slides down an inclined plane 8. 0 x 10-1 m long in 0. 50 s. What net force is acting on the mass along the incline?

Answers

The net force acting on the mass of 2.0 kg along the incline plane is 12.8 N.

What is force?

Force is the product of mass and acceleration.

To calculate the net force acting on the mass along the inclined plane, we use the formula below.

Formula:

F = m(2s/t²)........... Equation 1

Where:

F = Net forces = distancet = Time

From the question,

Given:

m = 2.0 kgs = 0.8 mt = 0.5 s

Substitute these values into equation 1

F = 2×2×0.8/0.5²F = 12.8 N

Hence, the net force of the mass is 12.8 N.

Learn more about  force here: https://brainly.com/question/25239010

#SPJ1

: In the spring of 2021, the New Horizons spacecraft reached a distance of 50 astronomical units ("AU") from Earth. At that time, how many km was New Horizons from Earth? Note: One astronomical unit is the distance from the Earth to the Sun or about 150 million km. Question 3 (6 points): The planet Mars completes one orbit of the Sun in 687 days. Use scientific notation to express this time in units of seconds. You may use the character ∧
for the power of 10 , like 4.5×10 ∧
4 (4.5 times 10 to the 4 th power).

Answers

The time taken by the planet Mars to complete one orbit of the Sun is 5.94 x 10⁷ seconds.

Given information: In the spring of 2021, the New Horizons spacecraft reached a distance of 50 astronomical units ("AU") from Earth. One astronomical unit is the distance from the Earth to the Sun or about 150 million km.

Calculation: To find how many km was New Horizons from Earth, we need to multiply the distance in AU by the conversion factor. 1 AU = 150 million km 50 AU = 50 x 150 million km = 7.5 billion km Thus, the New Horizons spacecraft was 7.5 billion km from Earth in the spring of 2021. Now, let's move on to the second question. The planet Mars completes one orbit of the Sun in 687 days. We need to express this time in seconds using scientific notation.

To convert days to seconds, we need to multiply the number of days by the conversion factor. 1 day = 86400 seconds 687 days = 687 x 86400 seconds= 5.94 x 10⁷ seconds (using scientific notation) Therefore, the time taken by the planet Mars to complete one orbit of the Sun is 5.94 x 10⁷ seconds.

To know more about Time and Distance here:

https://brainly.com/question/19773192

#SPJ11

A 15.0-kg block is dragged over a rough, horizontal surface by a 70.0-N force acting at 20.0° above the horizontal. The block is displaced 5.00 m, and the coefficient of kinetic friction is 0.300. Find the work done on the block by a) The 70-N force, b) The normal force, and c) The gravitational force. D) What is the increase in internal energy of the block-surface system due to friction? E) Find the total change in the block's kinetic energy.

Answers

Answer:

Explanation:

from the question we are told that

Load \(L=15kg\)

Force\(F=70N\)

Angle of inclination \(=20.0 degres\)

Displacement \(m=5 meters\)

coefficient of kinetic friction \(\alpha =0.300\)

Other Questions
What is x if f(x)=-2 Find the probability of the indicated event if P(E) = 0.20 and P(F) = 0.45.Find P(E or F) if P(E and F) = 0.10P(E or F) = ? (Simplify your answer) A forklift pushes a 185kg box into a 335kg box, which slides into a 80kg box. If all 3boxes slide across the floor at 4.5m/s, how much force does the 185kg box exert onthe 335kg box? The coefficient of friction between each box and the floor are listedin the table below: Money is functioning as a standard of value when you: Group of answer choices Use it to compare two houses that are different prices. Buy jeans at the mall. Buy a rare baseball card that you expect will increase in value. Trade a cup of sugar for two eggs. Anole Company was incorporated as a new business on January 1, 2015. The company is authorized to issue 20,000 shares of $5 par value common stock and 10,000 shares of 6%, $10 par value, cumulative, participating preferred stock. On January 1, 2015, the company issued 8,000 shares of common stock for $15 per share and 2,000 shares of preferred stock for $30 per share. Net income for the year ended December 31, 2015, was $375,000.1. Refer to the information about Anole Company.The amount of Anoles total contributed capital at December 31, 2015, is2. Refer to the information about Anole Company.The number of Anoles unissued shares of common stock at December 31, 2015, is3. Refer to the information about Anole Company.Anoles total stockholders' equity reported on the balance sheet at December 31, 2015, is:___________ What is the volume of a cylinder , whose base diameter us of 20cm and height of 5cm. If a firm in a competitive market doubles its number of units sold, total revenue for the firm will - more than double. - double. - increase but by less than double. - may increase or decrease depending on the price elasticity of demand love at first bite orders flour in 5-lb bags and sugar in 3-lb bags. their storage room currently has a maximum of 150 pounds of flour and sugar combined. is it possible that the bakery has 16 bags of flour and 20 bags of sugar? explain 33. Larshbonkh Corporation has a debt-to-equity ratio of 2. Its debt beta is zero and it does not pay any corporate taxes. Its asset beta is 1.2. What is Larchbonkh's equity beta? A. 2.4 B. 1.2 C. 2 D. 3.6 E. None of the above 34. Becauns, Corp has a debt-to-equity ratio of 0.3, Its debt beta is zero and its corporate tax rate is 40%. Its asset beta is 0.7. What is Becauns, equity beta? A. 0.426 B. 0.826 C. 0.784 D. 0.7 E. None of the above 2. Water can be understood as both yin and yang. Challenge: how many ways can you explain why ? 6,370 x 30 find the products How do I show my thinking or ideasExample6373 637030=1911 =(63703) (1010) why florida requiring female athletes to report periods ? what is the solution to this equation 7x-3(x-6)=30 A(n) _________________ schedule of reinforcement is used when a person is learning a new behavior. Which linear inequality represents the solution set graphed? A rectangular box is 2 cm high , 4 cm wide and 6 cm deep.Mavis packs the box with cubes, each 2cm by2cm by 2cm,with no space left over. How many cubes does Mavis fit into the box? idk how much is 10nnjaksbfuanjvhaiuvna These are two separate questions, please help. R is positive can someone simplify it ik it may actually be simple lol How to find (fg)(x) from the equation